If you would like to join the DLOC, please visit the Club's website https://www.dloc.org.uk/
Please don't post someone's email address. Some people don't want to risk it being harvested by spambots and GDPR regulations discourage it.
Always look at "ACTIVE TOPICS" which gives all posts in date & time order if you can't find a post or "Your Posts", as topics are sometimes moved.
Reg. nrs. Please add reg. nr. when posting a photo or anything about a car as this will help searches. Don't add punctuation next to nr. as this negates search.

v8 2.5 high oil pressure

tjt77
Posts: 473
Joined: Wed Mar 23, 2016 7:01 pm

Re: v8 2.5 high oil pressure

Post by tjt77 » Thu Apr 25, 2019 1:04 am

Buckfield :- the standard electrical gauges are notoriously innacurate.. they commonly read low with the passing of time .the issue is almost always the sender unit which is sensitive to heat exposure. Mechanical guages are known to be more reliable .. but obviously qualities vary.. the smith/british jaeger as used in MG's rarely give bad readings.. VDO are known to be good in both electrical and mechanical formats..

Chris_R
Posts: 415
Joined: Wed Feb 10, 2016 12:48 pm
Location: Twickenham

Re: v8 2.5 high oil pressure

Post by Chris_R » Thu Apr 25, 2019 10:10 am

Again, I agree with the preceding comment from my own experience. Different car but still an electrical sender that started reading very low and sometimes dropping to zero at idle. Temporarily adding a mechanical gauge allowed me to see what was really going on. The problem was the sender malfunctioning. Although you have the opposite issue, the mechanical gauge will provide backup data to what is happening.

classiclife
Posts: 268
Joined: Wed Sep 05, 2018 9:55 am
Location: Ridgewood - East Sussex
Contact:

Re: v8 2.5 high oil pressure

Post by classiclife » Thu Apr 25, 2019 6:59 pm

I presume that over time the oil sender unit (C15474) becomes less accurate and it may be the case that some cars will still have the original sender ??

A step forward, may well be substitution of the old unit for a new one.

Regards.

Richard.
1968 Daimler V8-250 Saloon
DLOC East Sussex Area Representative.

Southern Classics Society Events Co-ordinator.
www.southernclassics.org.uk

KV8
Posts: 197
Joined: Sun Mar 06, 2016 7:05 pm
Location: Cambridgeshire

Re: v8 2.5 high oil pressure

Post by KV8 » Thu Apr 25, 2019 10:14 pm

Steve laud wrote:
Mon Apr 22, 2019 4:16 pm
Hi Richard,oil was changed yesterday ,the new oil being castrol classic XL 20w/50
Interestingly Russ advised use of 15W40 following his rebuild of mine in 2015. Not sure what influence this would have if any on oil pressure readings but....

Regards

H

Tennant
Posts: 5
Joined: Sun Jan 20, 2019 7:13 pm
Location: Herne, Germany

Re: v8 2.5 high oil pressure

Post by Tennant » Tue Apr 30, 2019 10:55 pm

Hi Guys,
I was wondering about my oil pressure so bought a new sensor. I wanted to check it before fitting so removing the hose from a tyre compressor and screwing the sensor into the 1/8" connection in the tyre pump gauge. I could then earth the sensor and check the car gauge reading against the compressor reading. I found the car gauge reading low and the car gauge is adjustable using a screwdriver at the back of the gauge.
There is always the possibility that the compressor gauge is not correct but in my case the main compressor gauge and the hand gauge showed the same numbers so the probability is that they are correct.
Just my hack & I wish that I had the problem of high pressure!!

Barry

Post Reply