If you would like to join the DLOC, please visit the Club's website https://www.dloc.org.uk/
Please don't post someone's email address. Some people don't want to risk it being harvested by spambots and GDPR regulations discourage it.
Always look at "ACTIVE TOPICS" which gives all posts in date & time order if you can't find a post or "Your Posts", as topics are sometimes moved.
Reg. nrs. Please add reg. nr. when posting a photo or anything about a car as this will help searches. Don't add punctuation after nr. as this negates search.

Regency Rear Bumper

Post Reply
Posts: 8
Joined: Thu Jul 26, 2018 12:36 pm
Location: Southend on Sea, Essex, England

Regency Rear Bumper

Post by dtaylo30 » Wed Mar 06, 2019 12:51 pm

I have removed the rear bumper and am now struggling with how to remove the brackets from it. See pictures.
The brackets are slotted but the bumper studs are at opposing ends of the slots so the brackets are effectively locked in place.
Anybody know the solution?
20190306_094013 2.jpg
20190306_094013 2.jpg

Db n j
Posts: 216
Joined: Sun Mar 13, 2016 8:55 am

Re: Regency Rear Bumper

Post by Db n j » Wed Mar 06, 2019 8:02 pm

I'm not an expert at such a modern vehicle, but it looks like bolts through to captive nuts in the bracing-pieces.
So, use lots of freeing agent in advance, maybe heat before trying to turn the nut
(there is a fair chance the bolt will sheer anyway)

Good luck with the restoration !

Posts: 27
Joined: Fri Mar 18, 2016 6:59 pm
Location: Nijmegen, The Netherlands

Re: Regency Rear Bumper

Post by h.j.thomassen » Wed Mar 06, 2019 11:15 pm

One side has an ordinary nut. Maybe you could try a nut splitter on that one (Google for 'nut splitter')
and if the nut is off you might be able to wiggle to make the other side somewhat loose.
That might provide more room to get penetrating oil closer to the thread.


Posts: 501
Joined: Mon Feb 08, 2016 8:12 pm
Location: Northwich, Cheshire

Re: Regency Rear Bumper

Post by grahamemmett » Wed Mar 06, 2019 11:53 pm

I’d grind the nuts off flush with the bracket and punch it through. But there again I’m known for my butchery!

I will add that new bumper bolts are available from Namrick 😃
Graham Emmett
Northwich, Cheshire
DB18 1949 LCV522 (Yes that one with the P100s)

Posts: 395
Joined: Wed Feb 10, 2016 12:48 pm
Location: Twickenham

Re: Regency Rear Bumper

Post by Chris_R » Thu Mar 07, 2019 12:28 am

You're trying to remove that horizontal section of metal with two holes in the centre and mounted over a stud at each end? Looking at the condition it's possible that it has welded itself with rust to the metal where the stud is sitting. Perhaps get a hammer and chisel and attack the bracket from above and below the stud and see if you can get any movement.

Posts: 95
Joined: Sun Mar 13, 2016 11:35 am

Re: Regency Rear Bumper

Post by JDB » Thu Mar 07, 2019 9:22 am

Are you sure the stud is fixed to the welded mounting plate? I seem to remember on the Majestic Major, which has a mounting that looks the same as yours, that the stud is in fact a coach bolt and is loose in the welded mounting plate but captive due to the proximity of the main bumper body. It may be being held firm by a mix of rust and chrome plate, if you can get at least one of them moving you should have the clearance to remove the detachable bracket.

Posts: 8
Joined: Thu Jul 26, 2018 12:36 pm
Location: Southend on Sea, Essex, England

Re: Regency Rear Bumper

Post by dtaylo30 » Thu Mar 07, 2019 11:46 am

Thanks very much for all your replies.
I had assumed that the studs were welded to the plates welded to the bumper.
Captive bolts in slots makes sense as it would allow for some adjustment on assembly.
Tried looking under one of the inboard brackets with a mirror and torch and it does look like there is a bolt head under there.
So I am now hoping I can free the inboard studs. The outboard ones are pretty impossible to get to with the horizontal brackets in place.

Posts: 8
Joined: Thu Jul 26, 2018 12:36 pm
Location: Southend on Sea, Essex, England

Re: Regency Rear Bumper

Post by dtaylo30 » Fri Mar 08, 2019 11:39 am

On further investigation I found that the studs on the plates welded to the bumper are in fact weld studs and not captive bolts.
So the solution (after some thought): I got a big screw driver which I was able to get just under the outboard edge of the inner welded bumper bracket and heaved on it.
Doing this I was able to slightly flex the bracket enough to tip the stud very so slightly inboard so the horizontal bracket was able to lift and clear the stud.
Did the same at the other end and the horizontal brackets are off the bumper.

Post Reply