The photo shows what greeted me after I removed the cylinder head today. It looks like there was a helicoil already in use which failed. It doesn't look long enough to my inexperienced eye.
The challenge now is to find out what size and length thread insert I should use given that the stud hole in the block will have been enlarged to accept the (now failed) thread insert coil.
The thread on the stud is 3/8 inch BSF. Can anyone tell me what most likely size the hole will have been enlarged to?
I've never had to install a thread insert coil before, so all comments and recommendations are very welcome!
Please visit the Club's website https://www.dloc.org.uk/ to join. Visit https://www.dloc.org.uk/adhoc to DONATE towards the cost of the forum.
Please don't post someone's email address to avoid it being harvested by spambots and it's against GDPR regulations.
Always look at "ACTIVE TOPICS" to see all posts in date & time order as they are sometimes moved; or look at "Your Posts".
Please add Reg. nrs. when posting a photo or anything about a car as this will help searches. Don't add punctuation next to nr. as this negates search.
CHANGED YOUR EMAIL ADDRESS since registering?, click your username and check your address in User Control Panel, Profile, Account Settings.
If you want help to register, use "contact us" at page bottom for help.
Please don't post someone's email address to avoid it being harvested by spambots and it's against GDPR regulations.
Always look at "ACTIVE TOPICS" to see all posts in date & time order as they are sometimes moved; or look at "Your Posts".
Please add Reg. nrs. when posting a photo or anything about a car as this will help searches. Don't add punctuation next to nr. as this negates search.
CHANGED YOUR EMAIL ADDRESS since registering?, click your username and check your address in User Control Panel, Profile, Account Settings.
If you want help to register, use "contact us" at page bottom for help.
Daimler 15: stripped thread
- captain bobo
- Posts: 268
- Joined: Tue Feb 09, 2016 7:32 pm
- Location: Kimbolton, Cambs
-
- Man of Many Parts
- Posts: 673
- Joined: Fri Feb 12, 2016 8:44 pm
- Location: Derbyshire
Re: Daimler 15: stripped thread
The thread inserts have their own tap. You might be able to just screw in a new insert. Preferably you need to aim for a length of 1.5 times the diameter of the thread you are repairing.
Re: Daimler 15: stripped thread
That picture looks more like the stud has pulled the first 2 or 3 threads out of the block. You can't easily break a Helicoil and if they come out they are usually like a stretched spring. Helicoils are made out of what I would imagine is something like spring steel.You need to buy a 3/8 BSF Helicoil kit which usually have a variety of lengths of insert in the kit.
Nick
Nick
"Nick - do you think you will ever put that old car back together again?"
Re: Daimler 15: stripped thread
I only can agree Nick, this is not a Helicoil. It looks like the original threads of the block. The material of Helicoils is a lot more thick than than this string is.
Rolf
Rolf
Re: Daimler 15: stripped thread
Nick is correct. You need a 3/8" helicoil kit. The supplied drill and tap will be some size larger than 3/8" and drill out the hole large enough to be tapped for the helicoil to be screwed in but the result after you finish will be a 3/8" screwed hole into which your bolt will screw. Make sure you buy the correct 3/8" TPI (threads per inch) kit. UNC is 16, UNF is 24, Whitworth is also 16 but a different thread angle, BSF is 20, also a 55 degree angle.
-
- Wise Man
- Posts: 795
- Joined: Sat Feb 13, 2016 2:14 pm
- Location: Penkridge. Staffs.
Re: Daimler 15: stripped thread
I doubt the material clinging to the failed stud in your picture is the original thread from the block, as the block is cast iron - which does not form into a "wire-like" spiral if stripped.
You might be able to remove the old helicoil insert with a helicoil tap if that be the case, but the resolution might be more difficult if not.
What you will need to do is turn a "stepped" stud of the correct diameter for the cylinder head nut etc, but with an enlarged diameter to accept a similarly enlarge threaded hole in the block, or even the "next size up" helicoil for which you could dimensionally consider a metric size.
You might be able to remove the old helicoil insert with a helicoil tap if that be the case, but the resolution might be more difficult if not.
What you will need to do is turn a "stepped" stud of the correct diameter for the cylinder head nut etc, but with an enlarged diameter to accept a similarly enlarge threaded hole in the block, or even the "next size up" helicoil for which you could dimensionally consider a metric size.
- captain bobo
- Posts: 268
- Joined: Tue Feb 09, 2016 7:32 pm
- Location: Kimbolton, Cambs
Re: Daimler 15: stripped thread
I removed the "spring" from the stud and took this photo. I guess that it's a threaded insert judging by the consistent thickness and the cleanliness of the edges.
I've examined the hole in the block as closely as I can (strong torch beam and magnifying glass); the thread looks to be in good order.
When I screw in the head stud it turns with almost no resistance and there is very slight movement when fully screwed in which suggests to me that it has already been resized to accept a threaded insert such as a helicoil.
Can anyone suggest anything else I might consider and check before I buy and try to fit a 3/8 inch helicoil?
I've examined the hole in the block as closely as I can (strong torch beam and magnifying glass); the thread looks to be in good order.
When I screw in the head stud it turns with almost no resistance and there is very slight movement when fully screwed in which suggests to me that it has already been resized to accept a threaded insert such as a helicoil.
Can anyone suggest anything else I might consider and check before I buy and try to fit a 3/8 inch helicoil?
Best wishes, Dave B
-
- Wise Man
- Posts: 795
- Joined: Sat Feb 13, 2016 2:14 pm
- Location: Penkridge. Staffs.
Re: Daimler 15: stripped thread
Your almost home and dry!!
Given you have identified that the block had been helicoiled before and you have removed the old insert, you merely have to put in a new insert - and given the stud was passing through the cylinder head means the position of the old insert was dimensionally correct.
So, first measure the depth of the hole in the block, as that will be the length of insert to use (and you can cut them down). Now all you need to do is verify the thread size - which I believe has been verified by others to be 3/8 B.S.F. - which is 20 tpi. (threads per inch).
Has no-one on the forum got a helicoil kit that size, as all you need is one insert which you can buy seperately, rather than the costly kit which includes drill and tap etc. In fact, if you bought just the insert you could make the tool which allows you to screw it into te block.
Stan,
Given you have identified that the block had been helicoiled before and you have removed the old insert, you merely have to put in a new insert - and given the stud was passing through the cylinder head means the position of the old insert was dimensionally correct.
So, first measure the depth of the hole in the block, as that will be the length of insert to use (and you can cut them down). Now all you need to do is verify the thread size - which I believe has been verified by others to be 3/8 B.S.F. - which is 20 tpi. (threads per inch).
Has no-one on the forum got a helicoil kit that size, as all you need is one insert which you can buy seperately, rather than the costly kit which includes drill and tap etc. In fact, if you bought just the insert you could make the tool which allows you to screw it into te block.
Stan,
Re: Daimler 15: stripped thread
I don't believe the removed "spring" is part of a Helicoil because Helicoils are made of a round wire and of thicker wire material than this one. And this removed "spring" wire is flat shaped at the outside.
Rolf
Rolf
- Attachments
-
- tempart2-b7211-25.png (106.39 KiB) Viewed 465 times
- captain bobo
- Posts: 268
- Joined: Tue Feb 09, 2016 7:32 pm
- Location: Kimbolton, Cambs
Re: Daimler 15: stripped thread
Rolf, not all thread inserts are round in cross section: this extract from the web page of a UK based thread insert supplier explains that theirs are diamond shaped cross sections (the article goes on to explain why this cross section gives better performance for many engineering applications). I may be wrong, but I'm pretty sure what I removed from the stud was a thread insert with a non-round cross section.
Best wishes, Dave B